***UPDATE*** JLT Intakes are available and sound / look great !

[DemonWorks]

Great value for $449 in comparison to others on the market. I have been waiting for these to become available as well as many others on here. I saw Lethal post they had them available and a few days later they are installed ! Here is a video I made to show them installed as well as some sound clips.

Sponsored

 

[msquad]

Nice job and doesn't look too bad. Would the non-oiled, non-paper filters that you have work with the JLT?

 

[DemonWorks]

Unfortunately, they cannot. I would prefer those filters, I liked the test results and the quality from them. The reason they do not fit is due to the box design, the S&B filters pull through the box and don't actually attach to a tube.

For those wondering, these are the filters we are talking about:

 

[Mr Hyde]

Pardon the ignirance but how do they attach then?

 

[DemonWorks]

Pardon the ignirance but how do they attach then?

They pull through on the engine side. In this pic, you can see I actually do not have it pulled all the way through at the top. (edit- it is pulled all the way through, just appears to not be. Hopefully this pic helps though.

 

[Godzilla1959]

My JLT's delivered today. I ordered them Sunday so took five days. Going to install them tomorrow. I was considering these larger throttle bodies also but currently out of stock now. I'm assuming when a tune is available the JLT's and these throttle bodies could open up a little more horsepower/torque. Your video sounds great! Soler Performance SE-JL3E-90S2 Mustang GT/Dark Horse 90MM Throttle Bodies (2024+)

 

[Mr Hyde]

They pull through on the engine side. In this pic, you can see I actually do not have it pulled all the way through at the top. (edit- it is pulled all the way through, just appears to not be. Hopefully this pic helps though. The throttlebodies seem to be good may give some benifit but at 500 ish each that aloy of cash for minimal gain without a tune

Gotcha much easier to get the filter on.

 

[CT22]

So I installed my JLT on my DH like two weeks ago and immediately got a check engine like P010B MAF error. I clear it with and OBD it runs good the next drive but after tuning off and back on the check engine light come back on.

Anyone else having this issue?

Are tunes still not available? WTF!?

Also, anyone know if I run with the check engine light and this error, am I damaging my motor?

Thanks!

 

[DemonWorks]

So I installed my JLT on my DH like two weeks ago and immediately got a check engine like P010B MAF error. I clear it with and OBD it runs good the next drive but after tuning off and back on the check engine light come back on.

Anyone else having this issue?

Are tunes still not available? WTF!?

Also, anyone know if I run with the check engine light and this error, am I damaging my motor?

Thanks!

I did not get any check engine lights. I would take a look to make sure the maf is sealed against the tube with the gasket as well as make sure the pipes on the tubes aren't leaking. Lastly, the boots for the pipe to the throttle bodies is very flimsy and can easily be rolled at the throttle body. I am guessing that's where you may have your issue.

 

[highvoltage]

Unfortunately, they cannot. I would prefer those filters, I liked the test results and the quality from them. The reason they do not fit is due to the box design, the S&B filters pull through the box and don't actually attach to a tube.

For those wondering, these are the filters we are talking about:

my IATs came down doing that mod.

 

[DemonWorks]

I edited the first post to include an additional video showing the intakes do not seal up to the hood as advertised ...

***update- JLT/S&B reached out and I possibly received some defective boxes and we will work to get correct boxes to replace these.

 

[Joe_Stang]

I think I'll just stick with my high flow filters atleast until tuning comes out and maybe we can actually get some gains from intake systems. It just feels like throwing damn near $500 away for some noise at this point. Plus if it doesn't seal against the hood it's really pointless to me. I'm guessing they are supposed to seal against it but you got defective ones but I'm not taking that chance lol.

 

[CT22]

I edited the first post to include an additional video showing the intakes do not seal up to the hood as advertised ...

***update- JLT/S&B reached out and I possibly received some defective boxes and we will work to get correct boxes to replace these.

Hi. Did you get the new boxes from them yet? If so, how are they?
I have the same issue with sealing on the top with both sides

 

[DemonWorks]

Hi. Did you get the new boxes from them yet? If so, how are they?
I have the same issue with sealing on the top with both sides

I did not, they are going to be testing some new seals on the top of the boxes then sending me those. I suggest you reach out to them and let them know you have the issue as well.

 

[DemonWorks]

I wanted to provide an update to this intake- JLT / S&B worked with me on testing out some new seals and a little spacer on the driver side. We got the airbox to seal up to the hood about 95%. I'm pretty happy with this as it's the best value intake at this point and it achieves what I was after at the lowest price point. I also added some different silicone boots to the intake to clean it up. I am very happy with it and wanted to share my experience.

Sponsored