PCM module - block numbers have changed

[Sainty]

Solved:
downgrade the version of FORScan to 2.3.64
Use the latest version of FORScan. The block numbers have changed. See post #37 for official response from FORScan.


Hi all,

I know this is possible as I've seen people have managed to enable remote rev in the PCM module.
I'm sure there must be a simple explanation for the this - why is access to 7E0-02-04 not available?

Sponsored

 

[npole]

Probably because of your interface, I had the same issue (I was using an old OBD interface), then bought the "right" one and many other modules (and contents) appeared. What does it show in the PCM Module Configuration tab?

This: https://www.amazon.co.uk/Vgate-vLinker-Adapter-FORScan-MS-CAN/dp/B0952P4MLP/

 

[Sainty]

Thanks for the reply!

Now that is interesting, I have the exact same cable I think, however I purchased it here:

https://www.ebay.co.uk/itm/134561362042

 

[npole]

So it's not the cable... What does it show in the PCM Module Configuration tab?

 

[Sainty]

Just the blocks 162-165. Let me grab another screenshot

 

[Sainty]

 

[npole]

Unless it's your first time with FORSCAN (first time created a profile), try to delete the current profile and create a new one.
As said when I had a similar issue, it was the cable, but you deffo using my same (new) cable, so I doubt it's it.

 

[Sainty]

I've now tried everything I can think of:

• Clean install of FORScan version 2.3.65 after uninstalling and deleting C:\Users\{USER}\AppData\Roaming\FORScan
• Remove FTDI chip USB drivers and re-installed latest (v2.12.36.20)

Still no luck unfortunately. Thank you for your assistance though npole. I'll keep trying, and maybe I'll contact FORScan directly.

 

[A.alansari]

I tried today I got the same addresses as you this is my first time using forscan I was trying to enable remote rev as well but no luck

please update the post if you find a soloution

 

[GrabThatBlue]

I've heard PCM and BCM are partially locked. Not all lines are accessable. Not sure if it's true, but based on your experience it might be the case.

 

[Sainty]

I did have another thought:

Dark Horse = unrestricted PCM
Everything else = restricted PCM

I'm hoping this is not correct though!!

 

[zackmd1]

Just connected today for the first time and ran into the same issue... I want to enable SST for an EcoBoost without paddles but am only getting 162-165. Car is a Job 2 2024 (06/24 build).

BCM lines past 96 also do not appear so no walk away lock capability...

Did you contact the Forscan Team?

 

[Sainty]

No, I have not. I got distracted by other things unfortunately.
I may do now though, as clearly this is wider issue!

 

[GrabThatBlue]

Here they talked about a locked PCM

https://www.mustang7g.com/forums/threads/so-is-the-s650-pcm-locked-or-not.156282/page-5

 

[zackmd1]

Here they talked about a locked PCM

https://www.mustang7g.com/forums/threads/so-is-the-s650-pcm-locked-or-not.156282/page-5

The PCM is locked for tuning but others have been able to successfully edit the lines I am looking to edit. So either Ford made a change to later production 24s and into 25 or there is an issue with Forscan 2.3.65. Lets hope its a Forscan issue. I am contacting them to see what can be done.

Sponsored